Power Mode of High-Speed Combined Extrusion of Flat Bimetallic Road Milling Picks
https://doi.org/10.21122/2227-1031-2021-20-4-287-295
Abstract
The paper presents a mathematical model developed for calculating the force effect on the punch in the process of high-speed combined hot extrusion of bimetallic road milling picks under plane deformation conditions. To solve the problem, the process is divided into two phases: acceleration phase and braking phase, which consists of two stages. A distinctive feature of the acceleration phase is that it allows the analysis of reverse extrusion, in the process of which the metal flows in the opposite direction to the punch stroke. A method for calculating the force acting on the punch at each phase of the process of plastic flow of a bimetallic workpiece into a matrix cavity with three deformation zones is presented in the paper. While solving the problem in a quasi-static formulation and proceeding from the conditions of the minimum power of internal forces, equations have been obtained for calculating the optimal field parameters aopt, bopt, gopt, depending on the elongation coefficients l and the friction coefficient m. The equations obtained within the framework of the developed model are quite correct, since they allow determining the minimum force acting on the punch. The considered calculation model and equations can be used in the development of industrial technology for high-speed combined hot extrusion of flat-step bimetallic road milling picks.
About the Authors
K. Y. BykovBelarus
Minsk
I. V. Kachanov
Belarus
Address for correspondence: Kachanov Igor V. – Belаrusian National Technical University, 65, Nezavisimosty Ave., 220013, Minsk, Republic of Belarus, Tel: +375 17 292-76-77
hidrokaf@bntu.by
I. M. Shatalov
Belarus
Minsk
References
1. Kachanov I. V. (2002) High-Speed Hot Extrusion of Rod Products. Minsk, Tekhnoprint Publ. 327 (in Russian).
2. Zdor G. N., Isaevich L. A., Kachanov I. V. (2010) Technology of High-Speed Material Deformation. Minsk, Belarusian National Technical University. 456 (in Russian).
3. Kachanov I. V., Zdor G. N., Isaevich L. A., Sharii V. N. (2011) High-Speed Hot Extrusion of Core Products with Butt End Cladding. Minsk, Belarusian National Technical University. 198 (in Russian).
4. Kapranov V. N., Osinnykh V. Ya. (1977) Specific Features of Enhanced Accuracy Moulder Tool for High-Speed Hot Extrusion. Povyshenie Kachestva i Effektivnosti Izgo-tovleniia Tekhnologicheskoi Osnastki Metodami Plasticheskogo Deformirovaniia: Cb. Tez. Vsesoiuz. Nauch.-Tekhn. Konf. [Improvement of Quality and Efficiency in Manufacturing of Machine-Tool Attachments while Using Deformation Methods: Book of Abstracts of All-Union Scientific Research Conference]. Tallinn, 125–129 (in Russian).
5. Kachanov I. V., Vlasov V. V. (2018) Loading Regime Optimization for High-Speed Impact Extrusion of Bimetallic Flat-Step Rod Products. Vestsi Natsyyanal’nai Aka-demii Navuk Belarusi. Seryya Fizika-Technichnych Navuk = Proceedings of the National Academy of Sciences of Belarus. Physical-Technical Series, 63 (1), 43–52 (in Russian).
6. Kachanov I. V., Shary V. N., Vlasov V. V. (2016) Resource-Saving Technology for High-Speed Hot Extrusion of Bimetallic Rod Parts. Nauka i Tekhnika = Science & Technique, 15 (1), 3–8. https://doi.org/10.21122/2227-1031-2016-15-1-3-8 (in Russian).
7. Tutyshkin N. D. (1972) Ratio at Discontinuities under Dynamic Planar Deformation. Tekhnologiya Mashinostroeniya [Technology of Mechanical Engineering]. Tula, (29), 56–66 (in Russian).
8. Tomlenov A. D. (1972) Theory of Plastic Deformation of Metals. Moscow, Metallurgiya Publ. 408 (in Russian).
9. Storozhev M. V., Popov E. A. (1977) Theory of Metal Working with Pressure. Mosсow, Mashinostroenie Publ. 423 (in Russian).
10. Segal V. M. (1977) Technological Problems of the Plasticity Theory. Minsk, Nauka i Tekhnika Publ. 254 (in Russian).
11. Renne I. P., Tutyshkin N. D. (1972) The Calculation of Inertia Forces in the Flat Extrusion of a Strip Through Wedge Matrices. Izvestiya Vysshikh Uchebnykh Zave-deniy. Mashinostroenie [Proceedings of Higher Educational Institutions. Маchine Building], (6), 144–147 (in Russian).
12. Rabotnov Yu. N. (1988) Mechanics of a Deformable Solid Body. Mosсow, Nauka Publ. 654 (in Russian).
13. Kachanov I. V., Dyakonov O. M. (2002) Determination of the Force in the Process of Impact Extrusion of Flat Rod Products. Vestsi Natsyyanal’nai Akademii Navuk Belarusi. Seryya Fizika-Technichnych Navuk = Proceedings of the National Academy of Sciences of Belarus. Physical-Technical Series, (1), 77–81 (in Russian)
Review
For citations:
Bykov K.Y., Kachanov I.V., Shatalov I.M. Power Mode of High-Speed Combined Extrusion of Flat Bimetallic Road Milling Picks. Science & Technique. 2021;20(4):287-295. (In Russ.) https://doi.org/10.21122/2227-1031-2021-20-4-287-295