Preview

TO DETERMINATION OF INFLUENCE FOR VARIATIONS IN LASER TREATMENT MODES ON TRIBOLOGICAL CHARACTERISTICS OF CUTTING TOOL

https://doi.org/10.21122/2227-1031-2016-15-5-415-419

Abstract

The paper considers problems pertaining to higher durability and reliability of a cutting tool for cutting gastronomic products while using laser processing that leads to resistance increase of material operating surfaces against impact forces. Influence of laser fusion with additional doping on structure, microhardness, wear resistance for adhesive coatings of Fe–B–Cr–Si system has been studied in the paper. In order to solve a problem for selection of optimal qualitative and subsequently quantitative composition of a multi-component coating a mathematical modeling method using Scheffe’s simplex lattices has been used in the paper. Similar tendency for measuring micro-structure of all adhesive coatings fused by laser beams has been established in the paper. Increase in beam speed has caused the following microstructure changes: cast equilibrium, dendrite, supersaturated boride, carbide and boride. Response surface models have been found and they provide the possibility to assess influence quantity of laser processing parameters on microhardness of adhesive coatings obtained by laser doping and intensity of their wear under various conditions for all investigated compositions.It has been ascertained that there is no strict correlation between hardness and intensity of coating wear after laser doping used for adhesive coatings. This testifies to the fact that hardening has taken place not only due to an increase of carbide-boride phase, but also due to matrix hardening.In addition, a regression model for coating composition effect on tribological characteristics of the adhesive coatings has revealed that an optimal composition of a multicomponent coating ensuring maximum wear resistance of coatings constitutes B4C is 2/3 and 1/3 TaB. It has been determined that hardening of the adhesive coating after laser doping while using multicomponent coating occurs not only due to increase of carbide-boridnoy phase, but also due to matrix hardening.

About the Authors

O. V. Diachenko
Belarusian National Technical University
Belarus

Doctor of Engineering 

Address for correspondence: Diachenko Оlga V.— Belаrusian National Technical University, 67 Nezavisimosty Ave.,   220013, Minsk, Republic of Belarus Tel.: +375 17 293-95-81   tiro@bntu.by



M. A. Kardapolova
Belarusian National Technical University
Belarus

Doctor of Engineering 



O. V. Seriakova
Belarusian National Technical University
Belarus

Student



References

1. Latypov R. R.,Teregulov N. G., Smyslov A. M., Lobanov A. V. (2007) Technology of Laser Processing for Structural and Tool Materials in Aircraft Engine Manufacturing. Moscow, Mashinostroyenie. 240 (in Russian).

2. Grigoryants A. G., Shiganov I. N., Misyurov A. I. (2008) Technological Processes of Laser Processing. Moscow, Bauman Moscow State Technical University. 664 (in Russian).

3. Vaks E. D., Milenkii M. N., Saprykin L. G. (2013) Practice of Precision Laser Processing. Moscow, Tekhnosfera. 708 (in Russian).

4. Busnjuk N. N., Chernyak A. A. (2014) Mathematical Simulation. Minsk, Belarus. 214 (in Russian).

5. Busnjuk N. N., Chernyak A. A., Chernyak Zh. A. (2014) Mathematical Simulation. Practical Course. Minsk, Belarus. 295 (in Russian).

6. Matalytsky M. A., Khatskevich G. A. (2012) Probability Theory, Mathematical Statistics and Stochastic Processes. Minsk, Vysheyshaya Shkola. 720 (in Russian).

7. Samarsky A. A., Mikhailov A. P. (2005) Mathematics. Mathematical Simulation. Ideas. Methods. Examples. Moscow, Physical and Mathematical Literature. 320 (in Russian).

8. Trusova P. V. (2007) Introduction to Mathematical Simulation. Moscow: Publishing House “Logos”. 440 (in Russian).

9. Chernyak ?. ?., Chernyak Zh. A., Metelsky Yu. M. (2007) Mathematical Programming. Algorithmic Approach. Minsk, Vysheyshaya Shkola. 352 (in Russian).

10. Yudenkov V. A. (2013) Analysis of Variance. Minsk, Biosphere. 75 (in Russian).


Review

For citations:


Diachenko O.V., Kardapolova M.A., Seriakova O.V. TO DETERMINATION OF INFLUENCE FOR VARIATIONS IN LASER TREATMENT MODES ON TRIBOLOGICAL CHARACTERISTICS OF CUTTING TOOL. Science & Technique. 2016;15(5):415-419. (In Russ.) https://doi.org/10.21122/2227-1031-2016-15-5-415-419

Views: 1878


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2227-1031 (Print)
ISSN 2414-0392 (Online)