SELECTION OF METHOD FOR RESTORATION OF PARTS
https://doi.org/10.21122/2227-1031-2016-15-1-9-17
Abstract
The paper contains definitions for a process and a methodology for restoration of parts on the basis of the analysis of the known methods and their selection. Geometric parameters and operational properties that should be provided for restoration of parts have been determined in the paper. A process for selection of the required method for restoration parts has been improved and it makes it possible to synthesize an optimal process of the restoration according to a criterion of industrial resource consumption with due account of quality, productivity and security limits. A justification on measures that meet the required limits has been presented in the paper. The paper shows a direction of technical solutions that ensure complete use of residual life of repair fund parts. These solutions can be achieved through close application of all repair sizes of work-pieces with revision of their values, uniform removal of the allowance while cutting the work-pieces at optimum locating, application of coating processes only in technically justified cases, application of straightening with thermal fixing of its results or all-around compression of deformable elements. The paper proposes to limit a number of overhauls for the units together with restoration of basic and fundamental parts by two repairs for the whole period of their lifetime. Number of shaft journal building-up should be limited by one building-up operation throughout the whole life cycle of the part with the purpose to preserve its length within the prescribed limits. It has been recommended to expand an application area of volumetric plastic deformation of material in the form of thermoplastic distribution or reduction of repair work-pieces representing class of rotation bodies with holes that ensures an allowance to machine external and internal surfaces for nominal dimensions without coating. A structure of the coating material with fine inclusions of carbides or nitrides of metals and preferred orientation of structural components perpendicular to the restored surface under the influence of heat removal has been established in the paper. Due to surface plastic deformation the structure orientates fiber axis tangentially in the direction of relative sliding that inhibits growth of fatigue radially oriented cracks.
About the Author
V. P. Ivanov
Polotsk State University, Novoрolotsk
Belarus
Belarus
Professor, PhD in Engineering
Address for correspondence: Ivanov Vladimir P. Polotsk State University 29 Blohina str.,211440, Novopoltsk, Vitebsk Province, Republic of Belarus Tel.: +375 214 53-10-47 ivprem@tyt.by
References
1. Lyalyakin V. P., Ivanov V. P. (2004) Restoration and strengthening of machinery parts in agro-industrial complex of Russia and Belarus. Remont, vosstanovlenie, modernizatsia [Repair, restoration, modernization], (2), 2–7 (in Russian).
2. Shadrichev V. A. (1962) Fundamentals on selection of rational method for restoration of automobile parts while using metallic coatings. Moscow, Leningrad, Mashgiz. 296 p. (in Russian).
3. Shadrichev V. A. (1976) Fundamentals of technology for automotive engineering and automobile repair: Textbook for higher education institutions. Leningrad, Mashinostroenie, Leningrad Branch. 560 p. (in Russian).
4. Batishchev A. N. (1988) Methodology for substantiation of rational method for restoration of worn-out parts . Modern equipment and technological processes for restoration and strengthening of machinery parts. Abstracts of Reports at Scientific and Technical Conference of Comecon Countries “Remdetal-88” (October 17–21, 1988, Piatigorsk). Part. 1. Moscow, 23–24 (in Russian).
5. Vasiliev N. G., Galiev I. I., Vasilieva T. N. (1996) Selection of method for restoration of worn-out parts. Svarochnoe proizvodstvo [Welding Production], (7), 13–15 (in Russian).
6. Panteleenko F. I., Lialiakin V. P., Ivanov V. P., Konstantinov V. M. (2003) Restoration of machinery parts. Reference Book. Moscow, Mashinostroenie. 672 p. (in Russian).
7. Bellman R. (1957) Dynamic programming. Princeton U.P. 365 p. (Russ. ed.: Bellman R. (1960) Dinamicheskoe programmirovanie. ?oscow, Inostrannaya Literature. 400 p.)
8. Ivanov V. P., Kastriouk A. P. (2013) Substantiation of portion of accepted parts for repair fund and further application without repair operations. Agropanorama, (5), 38–44 (in Russian).
9. Kastriouk A. P. (2012) Investigations on possibility to machine a crankshaft neck for regular repair size. Agropanorama, (1), 38–41 (in Russian).
10. Kastriouk A. P., Vigerina T. V. (2011) Resource-saving processes for shaft restoration. Vestnik Belorusskoi gosudarstvennoi sel'skokhoziaistvennoi akademii [Bulletin of the Belarusian State Agricultural Academy], (2), 118–122 (in Russian).
11. Kastriouk A. P., Vigerina T. V. (2012) Resource-saving and quality of machinery component repair with restoration of their parts. Novopolotsk: Polotsk State University. 200 p. (in Russian).
12. Vigerina T. V. (2013) Tekhnologiia vosstanovleniia kolenchatykh valov dvigatelei iz vysokoprochnogo chuguna i konstruktsionnoi stali napyleniem, naplavkoi i poverkhnostnym plasticheskim deformirovaniem. Avtoref. dis. kand. tekhn. nauk [Technology for restoration of motor crankshafts made from high-strength cast-iron and constructional steel while using spraying, welding deposition and surface plastic deformation. Abstract of Ph.D. Thesis in Engineering Science]. Minsk. 23 p. (in Russian)
Review
For citations:
Ivanov V.P. SELECTION OF METHOD FOR RESTORATION OF PARTS. Science & Technique. 2016;15(1):9-17. (In Russ.) https://doi.org/10.21122/2227-1031-2016-15-1-9-17
Views:
3235
Email this article 