TECHNOLOGY FOR OBTAINING BIMETALLIC SHAPING PARTS OF DIE TOOLING USING METHOD OF HIGH-SPEED HOT EXTRUSION
Abstract
Processes of high-speed shaping changes and especially high-speed hot extrusion create efficient conditions for treatment of weakly plastic and poorly deformable materials which are widely used in tool making facilities. Due to the fact that high-speed stamping provides accurate billets with increased mechanical properties, it can be used as a technological process for manufacturing shaping parts of die tooling parts operating which are subjected to increased loads and wear.
The purpose of the paper is to carry out experimental investigations on the possibility to obtain a bimetallic tool where structural steel is considered as a basis of the tool and a working cavity is made of high-alloyed tool steel with its saving up to 90 %. A scheme of loading and geometry of conjugated surfaces of the composite billet have been developed in the paper. Technology for obtaining bimetallic shaping parts of die tooling with deformation at speed of vR = 40-50 m/s and composite billet temperature of T = 1150 °C has been experimentally tested with formation of a compound due to plastic flow of two billet parts on contact surface with removal of surface oxide films.
Microstructures of the bimetallic compounds obtained with the help of high-speed hot extrusion method for compositions of structural and high-alloy steels have been investigated and their high quality has been proved during the investigations. Dependences of micro-hardness distribution have been established outbound two- steel contact plane in the zone of connection that are characterized by a minimum micro-hardness value in the connection joint. Availability of more plastic zone in the contact plane contributes to reduction of residual stresses due to their relaxation in this zone and higher joint strength.
About the Authors
I. V. Kachanov
Belarusian National Technical University
Belarus
Belarus
M. V. Kudin
Belarusian National Technical University
Belarus
Belarus
S. A. Lenkevich
Belarusian National Technical University
Belarus
Belarus
References
1. Kachanov, I. V., Isaevich, L. A. (2002) High-Speed Hot Extrusion of Rod Items. Minsk, Tekhnoprint (in Russian).
2. Zdor, G. N., Isaevich, L. A., Kachanov, I. V. (2010) Technologies of High-Speed Material Deformation. Minsk, BNTU (in Russian).
3. Kachanov, I. V., Zdor, G. N., Isaevich, L. A., Sharii, V. N. (2011) High-Speed hot Extrusion of Rod Items with Butt End Cladding. Minsk, BNTU (in Russian).
4. Kapranov, V. N., Osinnykh, V. Ya. (1977) Specific Features of Enhanced Accuracy Moulder Tool for High-Speed Hot Extrusion. Povyshenie Kachestva i Effektivnosti Izgotovleniia Tekh-Nologicheskoi Osnastki Metodami Plasticheskogo Deformirovaniia: Cbornik Tezisov Vsesoiuznoi Nauch- no-Tekhnicheskoi Konferentsii [Improvement of Quality and Efficiency in Manufacturing of Machine-Tool Attachments Using Plastic Deformation Method. Book Of Abstracts of All-Union Scientific and Technical Conference]. Tallinn, 125-129 (in Russian).
5. Kakhar, A. Yu. (1977) Semi-Hot Extrusion of Die Cavities Made of Alloy Tool Steel. // Povyshenie Kachestva i Effektivnosti Izgotovleniia Tekh-Nologicheskoi Osnastki Metodami Plasticheskogo Defor-Mirovaniia: Cbornik Tezisov Vsesoiuznoi Nauchno-Tekhnicheskoi Konferentsii [Improvement of Quality and Efficiency in Manufacturing of Machine- Tool Attachments Using Plastic Deformation Method. Book of Abstracts of All-Union Scientific and Technical Conference]. Tallinn, 69-75 (in Russian).
6. Liasnikov, A. V. (1993) Formation of Die Mould and Die Cavities by Extrusion. St.Petersburg, Vneshtorgizdat (in Russian).
7. Shmykov, A. A. (1956) Reference Book for Heat- Treater. Moscow, Mashgiz (in Russian).
8. Gelman, A. S. (1970) Prnciples of Pressure Welding. Moscow, Mashinostroenie (in Russian).
9. Shorshorov, M. H., Kolesnichenko, V. A., Aliokhin, V. P. (1982) Vee-Shape Pressure Welding of Dissimilar Metals. Moscow, Metallurgy (in Russian).
10. Kachanov, I. V., Kudin, M. V., Lenkevich, S. A. (2011) Equipment and Technology for Obtaining Bimetallic Shaping Parts of Die Toolings Using High-Speed Hot Extrusion Method. Metallugiia. Respublikanskii Mezhvedomstvennyi Sbornik Nauchnykh Trudov [Metallurgy. Republican Interagency Collection of Research Papers]. Minsk: BNTU, 34 (1) (in Russian).
11. Kachanov, I. V., Isaevich, L. A., Zdor, G. N., Kudin, M. V., Shariy, V. N., Lenkevich, S. A. (2014) Method for Manufacturing Forming Tools. Patent Republic of Belarus No ? 20110763. Ofitsial'nyi Biulleten'. Izobreteniia. Poleznye Modeli. Promyshlennye Obraztsy [Official Bulletin. Invention. Utility Models. Industrial Designs.], 2 (in Russian).
Review
For citations:
Kachanov I.V., Kudin M.V., Lenkevich S.A. TECHNOLOGY FOR OBTAINING BIMETALLIC SHAPING PARTS OF DIE TOOLING USING METHOD OF HIGH-SPEED HOT EXTRUSION. Science & Technique. 2014;(4):65-70. (In Russ.)
Views:
1599
Email this article 