EXPERIMENTAL IMPACT ASSESSMENT OF PARAMETERS PERTAINING TO BLANK TWO-DIMENSIONAL CIRCULAR MOTION ON INTENSITY OF ITS CUTTING AND QUALITY OF MACHINED SURFACE

The purpose of the paper is to make an experimental impact assessment of parameters pertaining to blank two-dimensional circular blank motion on intensity of its cutting and quality of the machined surfaces. Experimental data have been obtained that reveal efficiency in application of blank circular motion and improvement of its output cutting indices.

A methodology has been developed for execution of comparative experimental investigations on cutting glass, nephrite and jasper specimens as under conventional conditions required for the operation so while transferring induced oscillations to boom suspension assembly that ensure specimen.

The proposed methodology makes it possible to assess quantitatively intensity of specimen cutting and quality of its machined surface. The paper has shown that a positive impact of the specimen circular motion on quality improvement of its cross-cut surface is related to peculiar kinematics features pertaining to relative motion of disc side surface with cross-cut portions of the specimen surface. It has been shown that the intensifying impact of the specimen circular motion on the cutting process is primarily related to the changes in dynamic conditions of its interaction with the cutting edge of the disc. In contrast to conventional cutting when the process is going on under static pressure of contacting surfaces there is their periodical impact-frictional interaction due to transfer of circular motion to the specimen along elliptical trajectory. In this case the rate of the positive impact of the specimen circular motion on its cross-cut surface becomes higher while increasing vertical velocity component that concerns its sliding relative to disc side surface that is ensured by increasing oscillation frequency which is transferred to the boom suspension assembly. Moreover, the rate of positive impact of the specimen circulatory motion on the quality of its cross-cut surface becomes higher while increasing vertical velocity component of its sliding relative to disc surface.

1. Epifanov, V. I., Lesina, A. Ya., Zykov, L. V.(1987) Technology of Rough Diamond Processing in Polished Diamonds. Moscow, Higher School (in Russian).

2. Bykhovsky, N. N. (1968) Theoretical Principles of Vibration Engineering. Moscow, Mechanical Engineering (in Russian).

3. Drozdov, A. V. Povyshenie Proizvoditel'nosti i Ka- chestva Raspilivaniia Sverkhtverdykh Kristallov Putem Soob- shcheniia Zagotovke Vynuzhdennykh Kolebanii. Avtoref. dis. kand. tekhn. nauk [Increase in Productivity and Quality of Superhard Crystal Sawing by Transmitting Induced Oscillations to a blank. Author’s Abstract for a Science Degree of Candidate of Engineering Sciences]. Minsk, 2005 (in Russian).

4. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2011) Increase in Intensity and Quality of Hard and Super- Hard Materials by Transmitting a Two-Dimensional Circulatory Motion to a Blank. Vestnik BNTU [Bulletin of the Belarusian National Technical University], 5, 36-40 (in Russian).

5. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2011) Unit for Diamond Mono-Crystal Sawing by Transmitting a Periodical Circulatory Motion to a Blank. Vestnik Gomel'skogo Gosudarstvennogo Tekhnicheskogo Universiteta im. P. O. Sukhogo [Bulletin of P. O. Sukhoi State Technical University of Gomel], 2, 3-9 (in Russian).

6. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2013) Influence of Excitation Conditions of Sawing Section Boom on Parameters of Blank Oscillatory Motion. Materialy, Tekhnologii, Instrument [Materials, Technologies, Tools], 18 (1), 78-85 (in Russian).

7. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2013) Influence of Two-Dimensional Oscillatory Motion Transmitted to a Blank on Power and Time Parameters of its Contact Interaction with a Sawing Disk. Nauka i Tekhnika [Science and Technique], 1, 19-25 (in Russian).

8. Kiselev, M. G., Galeniouk, G. A., Drozdov, A. V. (2004) Theoretical Evaluation of Ultrasound Influence on Increase in Productivity of Mechanical Process for Sawing Mono-Crystals of Super-Hard Materials. Vesty Akademii Nauk Belarusi. Seriia Fiziko-Tekhnicheskikh Nauk [Bulletin of Academy of Sciences of Belarus. Series: Physical and Engineering Sciences], 2, 55-59 (in Russian).

9. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2011) Substantiation of Possible Blank Circulatory Oscillation in the Process of its Mechanical. Mezhdunarodnyi Simpozium "Perspektivnye Materialy i Tekhnologii ”, 24-26 maia 2011 g. Sbornik Statei [International Symposium “Prospective Materials and Technologies” May, 24-26 2011. Collected Works. Vitebsk: Vitebsk State Technological University, 4143 (in Russian).

10. Kiselev, M. G., Drozdov, A. V., Yamnaya, D. A. (2012) Methodology for Determination of Spatial and time Parameters of Contact Interaction of Oscillating Blank with Sawing Disk. Metrologia i Priborostroyenie [Metrology and Instrumentation], 2, 26-29 (in Russian).