Preview

НАУКА и ТЕХНИКА

НАУКА и ТЕХНИКА

Расширенный поиск

Обзор современного состояния технологий формирования многослойных покрытий на основе композиционных плазменных покрытий с никельсодержащими порошками

https://doi.org/10.21122/2227-1031-2026-25-5-375-389

Аннотация

В статье представлен обзор современного состояния технологий формирования многослойных покрытий на основе композиционных плазменных покрытий с использованием никельсодержащих порошков. Актуальность исследований обусловлена возрастающей потребностью в создании высокоэффективных защитных систем, способных работать в условиях повышенных температур, интенсивного износа, агрессивных сред, а также циклических механических и тепловых нагрузок. Подобные покрытия находят широкое применение в энергетическом машиностроении, авиационно-космической и других отраслях промышленности, где требуется повышение ресурса и надежности деталей и узлов. Показано, что традиционные однослойные покрытия не всегда способны обеспечить необходимое сочетание эксплуатационных характеристик. В связи с этим особый интерес представляют многослойные и функционально-градиентные покрытия, позволяющие объединить в одной системе высокую адгезионную прочность, износои термостойкость, устойчивость к коррозионному воздействию. Одним из наиболее эффективных методов их получения является плазменное напыление, обеспечивающее возможность регулирования фазового состава, пористости, микроструктуры и физико-механических свойств покрытия. В работе рассмотрены различные системы термобарьерных покрытий на основе NiCrAlY, NiCoCrAlY, ZrO2 – Y2O3, Al2O3 и HfO2 – Y2O3. Установлено, что введение плотных слоев оксида алюминия существенно повышает стойкость покрытий к горячей коррозии за счет снижения проникновения расплавленных солей в керамические слои. Функционально-градиентные покрытия ZrO2/NiCoCrAlY характеризуются постепенным изменением коэффициента теплового расширения и модуля упругости, что способствует уменьшению остаточных напряжений и повышению устойчивости к термоциклическому разрушению. Особое внимание уделено покрытиям на основе оксида гафния, обладающим высокой температурной стабильностью, низкой теплопроводностью и повышенной устойчивостью к фазовым превращениям. Для компенсации различий коэффициентов теплового расширения между металлическими и керамическими слоями предложено применение переходных слоев на основе диоксида циркония. Сделан вывод о том, что многослойные и функционально-градиентные плазменные покрытия являются перспективным направлением повышения долговечности и эксплуатационной надежности деталей машин и оборудования. Дальнейшие исследования должны быть направлены на совершенствование технологий плазменного напыления, оптимизацию состава порошковых материалов и разработку методов управления структурой и свойствами покрытий в соответствии с конкретными условиями эксплуатации.

Об авторах

О. Г. Девойно
Белорусский национальный технический университет
Беларусь

Доктор технических наук, профессор
г. Минск



В. В. Оковитый
Белорусский национальный технический университет
Беларусь
Адрес для переписки:

Оковитый Василий Вячеславович
 ул. Я. Коласа, 22/2,
220013, г. Минск,
Тел.: +375 17 293-93-71
niil_svarka@bntu.by



А. А. Литвинко
Белорусский национальный технический университет
Беларусь

Кандидат технических наук
г. Минск



В. Ю. Середа
Белорусский национальный технический университет 
Беларусь

Кандидат технических наук
г. Минск



В. М. Асташинский
Институт тепло- и массообмена имени А. В. Лыкова НАН Беларуси
Беларусь

Член-корреспондент НАН Беларуси, доктор физико-математических наук, профессор
г. Минск



Список литературы

1. Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3-ZrO2 Eutectics / J. Llorca, J. Y. Pastor, P. Poza [et al.] // Journal of the American Ceramic Society. 2004. Vol. 87, No 4. P. 633–639. https://doi.org/10.1111/j.1551-2916.2004.00633.x

2. Colony Structure in Ce-Doped Al2O3/YAG Eutectic Systems Grown by Vertical Bridgman Technique / S. Yamada, M. Yoshimura, S. I. Sakata [et al.] // Journal of Crystal Growth. 2016. Vol. 448. P. 1–5. https://doi.org/10.1016/j.jcrysgro.2016.05.003

3. High-Resolution Stress Mapping of Al2O3/Monoclinic ZrO2 and Al2O3/Cubic ZrO2(Y2O3) Eutectics Using Scanning Near-Field Optical Microscopy / S. Fukura, H. Kagi, M. Nakai [et al.] // Journal of Crystal Growth. 2009. Vol. 311. P. 998–1004. https://doi.org/10.1016/j.jcrysgro.2008.09.150

4. Crystallography and Interfacial Structure in a Directionally Solidified Al2O3/Y3Al5O12/ZrO2 Eutectic Crystal / X. Wang, Y. Zhong, Q. Sun [et al.] // Scripta Materialia. 2018. Vol. 145. P. 23–27. https://doi.org/10.1016/j.scriptamat.2017.10.008

5. Microstructures and Mechanical Properties of Directionally Solidified Al2O3/GdAlO3 Eutectic Ceramic by Laser Floating Zone Melting with High Temperature Gradient / H. Su, Q. Ren, J. Zhang [et al.] // Journal of the European Ceramic Society. 2017. Vol. 37, No 4. P. 1617–1626. https://doi.org/10.1016/j.jeurceramsoc.2016.11.041

6. Microstructure and Hardness Scaling in Laser-Processed B4C-TiB2 Eutectic Ceramics / R. M. White, J. M. Kunkle, V. Polotai, E. C. Dickey // Journal of the European Ceramic Society. 2011. Vol. 31, No 7. P. 1227–1232. https://doi.org/10.1016/j.jeurceramsoc.2010.06.013

7. Sola, D. Directionally Solidified Fabrication in Planar Geometry of Al2O3–Er3Al5O12 Eutectic Composite for Thermophotovoltaic Devices / D. Sola, P. B. Oliete, J. I. Peña // Optics Express. 2016. Vol. 24, No 10. P. A823-A831. https://doi.org/10.1364/oe.24.00a823

8. Merino, R. I. Compositionally Graded YSZ-NiO Composites by Surface Laser Melting / R. I. Merino, J. I. Peña, V. M. Orera // Journal of the European Ceramic Society. 2010. Vol. 30, No 2. P. 147–152. https://doi.org/10.1016/j.jeurceramsoc.2009.04.031

9. ZrO2-Al2O3 Eutectic Plates Produced by Laser Zone Melting / A. Larrea, G. F. de la Fuente, R. I. Merino,V. M. Orera // Journal of the European Ceramic Society. 2002. Vol. 22, No 2. P. 191–198. https://doi.org/10.1016/s0955-2219(01)00279-5

10. Laser-Assisted, Crack-Free Surface Melting of Large Eutectic Ceramic Bodies / J. Gurauskis, V. Lennikov, G. F. de la Fuente, R. I. Merino // Journal of the European Ceramic Society. 2011. Vol. 31, No 7. P. 1251–1256. https://doi.org/10.1016/j.jeurceramsoc.2010.08.017

11. Ester, F. J. Surface Modification of Al2O3–ZrO2(Y2O3) Eutectic Oxides by Laser Melting: Processing and Wear Resistance / F. J. Ester, R. I. Merino, J. Y. Pastor [et al.] // Journal of the American Ceramic Society. 2008. Vol. 91, No 11. P. 3552–3559. https://doi.org/10.1111/j.1551-2916.2008.02728.x

12. Ester, F. J. Processing and Microstructural Study of Surface Laser Remelted Al2O3–YSZ–YAG Eutectic Plates / F. J. Ester, A. Larrea, R. I. Merino // Journal of the European Ceramic Society. 2011. Vol. 31, No 7. P. 1257–1268. https://doi.org/10.1016/j.jeurceramsoc.2010.08.016

13. Insights into Microstructural Formation of Pulse Plasma Semi-Solid to Liquid Processing of Al2O3–ZrO2 Eutectic Ceramics / Z. G. Wang, J. H. Ouyang, Y. H. Ma [et al.] // Journal of the American Ceramic Society. 2018. Vol. 101, No 9. P. 3773–3779. https://doi.org/10.1111/jace.15715

14. Solidification Microstructure of Laser Remelted Al2O3–ZrO2 Eutectic / S. Bourban, N. Karapatis, H. Hofmann, W. Kurz // Acta Materialia. 1997. Vol. 45, No 12. P. 5069–5075. https://doi.org/10.1016/s1359-6454(97)00198-5

15. Correlations of Melt Pool Geometry and Process Parameters during Laser Metal Deposition by Coaxial Process Monitoring / S. Ocylok, E. Alexeev, S. Mann [et al.] // Physics Procedia. 2014. Vol. 56. P. 228–238. https://doi.org/10.1016/j.phpro.2014.08.167

16. Densification Behavior, Microstructure Evolution, and Wear Performance of Selective Laser Melting Processed Commercially Pure Titanium / D. Gu, Y. C. Hagedorn, W. Meiners [et al.] // Acta Materialia. 2012. Vol. 60. No 9. P. 3849–3860. https://doi.org/10.1016/j.actamat.2012.04.006

17. Li, M. On the Origin of Rcalescence Behaviors of Undercooled Single-Phase Mullite and Double-Phase Al2O3–ZrO2 Eutectic Melts / M. Li, K. Nagashio, K. Kuribayashi // Scripta Materialia. Vol. 47, No 4. P. 213–218. https://doi.org/10.1016/s1359-6462(02)00105-7

18. Microstructure evolution of laser remelted Al2O3– 13wt.%TiO2 coatings / S. G. Li, Z. S. Yu, Y. F. Zhang [et al.] // Journal of Alloys and Compounds. 2013. Vol. 576. P. 187–194. https://doi.org/10.1016/j.jallcom.2013.04.100

19. Liang, B. Thermal Resistance of Nanostructured and Conventional Zirconia Coatings Deposited by Atmospheric Plasma Spraying / B. Liang, C. Ding // Surface and Coatings Technology. 2005. Vol. 197, No 2–3. P. 185–192. https://doi.org/10.1016/j.surfcoat.2004.08.225

20. Thermal shock behavior of 8YSZ and double-ceramiclayer La2Zr2O7/8YSZ thermal barrier coatings fabricated by atmospheric plasma spraying / L. Wang, Y. Wang, H. Sun [et al.] // Ceramics International. 2012. Vol. 38, No 5. P. 3595–3606. https://doi.org/10.1016/j.ceramint.2011.12.076

21. Bose, S. High-Temperature Coatings / S. Bose. Butterworth-Heinemann, 2017. https://doi.org/10.1016/b978-0-7506-8252-7.x5000-8

22. Davis, J. R. Handbook of Thermal Spray Technology / J. R. Davis. ASM International, 2004.

23. Tsai, P. C. High-Temperature Corrosion Resistance and Microstructural Evaluation of Laser-Glazed PlasmaSprayed Zirconia/MCrAlY Thermal Barrier Coatings / P. C. Tsai, C. S. Hsu // Surface and Coatings Technology. 2004. Vol. 183, No 1. P. 29–34. https://doi.org/10.1016/j.surfcoat.2003.08.090

24. Tsai, H. Microstructures and Properties of Laser-Glazed Plasma-Sprayed ZrO2-YO1.5/Ni-22Cr-10AI-1Y Thermal Barrier Coatings / H. Tsai, P. Tsai // Journal of Materials Engineering and Performance. 1995. Vol. 4, No 6. P. 689–696. https://doi.org/10.1007/bf02646445

25. McPherson, R. Formation of Metastable Phases in Flameand Plasma-Prepared Alumina / R. McPherson // Journal of Materials Science. 1973. Vol. 8, No 6. P. 851–858. https://doi.org/10.1007/bf02397914

26. Soleimanipour, Z. Improving the Thermal Shock Resistance of Thermal Barrier Coatings Through Formation of an In Situ YSZ/Al2O3 Composite via Laser Cladding / Z. Soleimanipour, S. Baghshahi, R. Shoja-razavi // Journal of Materials Engineering and Performance. 2017. Vol. 26, No 4. P. 1890–1899. https://doi.org/10.1007/s11665-017-2591-0

27. Liu, Y. Experimental and Numerical Life Prediction of Thermally Cycled Thermal Barrier Coatings / Y. Liu, C. Persson, J. Wigren // Journal of Thermal Spray Technology. 2004. Vol. 13, No 3. P. 415–423. https://doi.org/10.1361/10599630420399

28. Zhou, C. Comparison of Thermal Cycling Behavior of Plasma-Sprayed Nanostructured and Traditional Thermal Barrier Coatings/ C. Zhou, N. Wang, H. Xu // Materials Science and Engineering: A. 2007. Vol. 452–453. P. 569–576. https://doi.org/10.1016/j.msea.2006.11.027

29. Laser Remelting of Zirconia Surface: Investigation into Stress Field and Microstructures / B. S. Yilbas, S. S. Akhtar, A. Matthews, C. Karatas // Materials and Manufacturing Processes. 2011. Vol. 26, No 10. P. 277–1287. https://doi.org/10.1080/10426914.2011.551955

30. Ouyang, J. H. Laser Remelting of Plasma-Sprayed Yttria Partially Stabilized Zirconia Coatings / J. H. Ouyang, X. D. Li // Journal of Materials Engineering and Performance. 2000. Vol. 9, No 5. P. 516–521. https://doi.org/10.1361/105994900770345638

31. Shankar, A. R. Laser Surface Modification of Plasma Sprayed Yttria Stabilised Zirconia Coatings on Type 316L Stainless Steel / A. R. Shankar, U. K. Mudali // Surface Engineering. 2009. Vol. 25, No 3. P. 241–248. https://doi.org/10.1179/174329408x326434

32. Laser Remelting of Plasma Sprayed Al2O3 Ceramic Coatings and Subsequent wear Resistance / Y. Yuanzheng, Z. Youlan, L. Zhengyi, C. Yuzhi // Materials Science and Engineering: A. 2000. Vol. 291, Iss. 1–2. P. 168–172. https://doi.org/10.1016/s0921-5093(00)00983-7

33. Bansal, P. Improved Interfacial Mechanical Properties of Al2O3–13wt%TiO2 plasma-Sprayed Coatings Derived from Nanocrystalline Powders / P. Bansal, N. P. Padture, Vasiliev // Acta Materialia. 2003. Vol. 51, No 10. P. 2959–2970. https://doi.org/10.1016/s1359-6454(03)00109-5

34. Microstructure Development of Al2O3–13wt.%TiO2 Plasma Sprayed Coatings Derived from Nanocrystalline Powders / D. Goberman, Y. H. Sohn, L. Shaw [et al.] // Acta Materialia. 2002. Vol. 50, No 5. P. 1141–1152. https://doi.org/10.1016/s1359-6454(01)00414-1

35. Indentation Fracture Behavior of Plasma-Sprayed Nanostructured Al2O3–13wt.%TiO2 Coatings / H. Luo, D. Goberman, L. Shaw, M. Gell // Materials Science and Engineering: A. 2003. Vol. 346. P. 237–245. https://doi.org/10.1016/s0921-5093(02)00523-3

36. Oxidation and Degradation of a Plasma-Sprayed Thermal Barrier Coating System / J. A. Haynes, E. D. Rigney, M. K. Ferber, W. D. Porter // Surface and Coatings Technology. 1996. Vol. 86–87. P. 102–108. https://doi.org/10.1016/s0257-8972(96)02985-4

37. Laser Remelting of Plasma Sprayed Nanostructured Al2O3–TiO2 Coatings At Different Laser Power / Y. Wang, C.G. Li, L. Guo, W. Tian // Surface and Coatings Technology. 2010. Vol. 204, No 201–202. P. 3559–3566. https://doi.org/10.1016/j.surfcoat.2010.04.028

38. Effects of the Laser Treatment and Thermal Oxidation Behavior of CoNiCrAlY/ZrO2–8wt%Y2O3 Thermal Barrier Coating / J. H. Park, J. S. Kim, K. H. Lee [et al.] // Journal of Materials Processing Technology. 2008. Vol. 201, No 1–3. P. 331–335. https://doi.org/10.1016/j.jmatprotec.2007.11.192

39. Fabrication and Evaluation of Plasma Sprayed Nanostructured Alumina–Titania Coatings with Superior Properties / E. H. Jordan, M. Gell, Y. H. Sohn [et al.] // Materials Science and Engineering: A. 2001. Vol. 301, No 1. P. 80–89. https://doi.org/10.1016/s0921-5093(00)01382-4

40. Effects of Critical Plasma Spray Parameter and Spray Distance on Wear Resistance of Al2O3–8 wt.%TiO2 Coatings Plasma-Sprayed with Nanopowders / E. P. Song, J. Ahn, S. Lee, N. J. Kim, // Surface and Coatings Technology. 2008. Vol. 202. P. 3625–3632. https://doi.org/10.1016/j.surfcoat.2008.01.002

41. Limarga, A.M. Mechanical Properties and Oxidation Resistance of Plasma-Sprayed Multilayered Al2O3/ZrO2 Thermal Barrier Coatings / A. M. Limarga, S. Widjaja, T. H. Yip // Surface and Coatings Technology. 2005. Vol. 197, No 1. P. 93–102. https://doi.org/10.1016/j.surfcoat.2005.02.087

42. Chen, D. Y. Microstructure of Suspension Plasma Spray and Air Plasma Spray Al2O3–ZrO2 Composite Coatings / D. Y. Chen, E. H. Jordan, M. Gell // Journal of Thermal Spray Technology. 2009. Vol. 18, No 3. P. 421–426. https://doi.org/10.1007/s11666-009-9306-5

43. Strangman, T. E. Thermal Barrier Coatings for Turbine Airfoils / T. E. Strangman // Thin Solid Films. 1985. Vol. 127, No 1–2. P. 93–105. https://doi.org/10.1016/0040-6090(85)90215-9

44. Shanker, A. R. Plasma-Sprayed Yttria-Stabilized Zirconia Coatings on Type 316L Stainless Steel for Pyrochemical Reprocessing Plant / A. R. Shanker, U. K. Mudali, R. Sole [et al.] // Journal of Nuclear Materials. 2008. Vol. 372, Iss. 2–3. P. 226–232. https://doi.org/10.1016/j.jnucmat.2007.03.175


Рецензия

Для цитирования:


Девойно О.Г., Оковитый В.В., Литвинко А.А., Середа В.Ю., Асташинский В.М. Обзор современного состояния технологий формирования многослойных покрытий на основе композиционных плазменных покрытий с никельсодержащими порошками. НАУКА и ТЕХНИКА. 2026;25(5):375-389. https://doi.org/10.21122/2227-1031-2026-25-5-375-389

For citation:


Devoino O.G., Okovity V.V., Litvinko А.А., Sereda V.Yu., Astashinsky V.A. Review of the Сurrent State of Technologies for Forming Multilayer Coatings Based on Composite Plasma-Sprayed Coatings with Nickel-Containing Powder. Science & Technique. 2026;25(5):375-389. (In Russ.) https://doi.org/10.21122/2227-1031-2026-25-5-375-389

Просмотров: 87

JATS XML


Creative Commons License
Контент доступен под лицензией Creative Commons Attribution 4.0 License.


ISSN 2227-1031 (Print)
ISSN 2414-0392 (Online)