Preview

Organization of Six-Cylinder Tractor Diesel Working Process

https://doi.org/10.21122/2227-1031-2021-20-5-427-433

Abstract

The purpose of the work is to consider the organization of the working process of six-cylinder diesel engines with a power of 116 and 156 kW and exhaust gas recirculation. The following systems and components were used in the experimental configurations of the engine: Common Rail BOSСH accumulator fuel injection system with an injection pressure of 140 MPa, equipped with electro-hydraulic injectors with seven-hole nozzle and a 500 mm3 hydraulic flow; direct fuel injection system with MOTORPAL fuel pump with a maximum injection pressure of 100 MPa, equipped with MOTORPAL and AZPI five-hole nozzle injectors; two combustion chambers with volumes of 55 and 56 cm3 and bowl diameters of 55.0 and 67.5 mm, respectively; cylinder heads providing a 3.0–4.0 swirl ratio for Common Rail system, 3.5–4.5 for mechanical injection system. The recirculation rate was set by gas throttling before the turbine using a rotary valve of an original design. The tests have been conducted at characteristic points of the NRSC cycle: minimum idle speed 800 rpm, maximum torque speed 1600 rpm, rated power speed 2100 rpm. It has been established that it is possible to achieve the standards of emissions of harmful substances: on the 116 kW diesel engine using of direct-action fuel equipment and a semi-open combustion chamber; on the 156 kW diesel using Common Rail fuel supply system of the Low Cost type and an open combustion chamber.

About the Authors

G. M. Kuharonak
Белорусский национальный технический университет
Belarus

Address for correspondence: Kuharonak Georgy M. Belаrusian National Technical University, 12, Ya. Kolasa str., 220013, Minsk, Republic of Belarus. Tel.: +375 17 292-81-86
kux@tut.by



M. Klesso
Minsk Motor Plant
Belarus

Minsk



A. Predko
Minsk Motor Plant
Belarus

Minsk



D. Telyuk
Minsk Motor Plant
Belarus

Minsk



References

1. Sevizdral S. P., Berezun V. I. (2013) State of Issue and Prospects for Development of Engine-Building in the Republic of Belarus. Zhurnal Assotsiatsii Avtomobilnykh Inzhenerov = Zurnal AAI, (6), 6–7 (in Russian).

2. Eurasian Economic Commission (2012) TR TS 031/2012. On Safety of Agricultural and Forestry Tractors and Trailers to Them. Minsk, Ekonomenergo Publ. 60 (in Russian).

3. United Nations (1986) Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts. Done at Geneva on 20 March 1958. Addendum 23: Regulation No 24 to be Annexed to the Agreement Revision 2 Incorporating the 03 Series of Amendments which Entered into Force on 20 April 1986. Available at: https://unece.org/ fileadmin/DAM/trans/main/wp29/wp29regs/r024r2e.pdf.

4. United Nations (2013) Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which Can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions. (Revision 2, Including the Amendments which Entered into Force on 16 October 1995). Addendum 95 –

5. Regulation No 96. Revision 2 – Amendment 1 Supplement 1 to the 03 Series of Amendments – Date of Entry into Force: 15 July 2013. Uniform Provisions Concerning the Approval of Compression Ignition (C.I.) Engines to be Installed in Agricultural and Forestry Tractors and in Non-Road Mobile Machinery with Regard to the Emissions of Pollutants by the Engine. Available at: https://unece. org/fileadmin/DAM/trans/main/wp29/wp29regs/2013/R09 6r2am1e.pdf.

6. Markov V. A., Bashirov R. M., Gabitov I. I. (2002) Diesel Exhaust Gas Toxicity. Moscow, Publishing House of Bauman Moscow State Technical University. 376 (in Russian).

7. Basshuysen R., Schäfer F. (2007) Handbuch Verbrennungsmotor. Grundlagen, Komponenten, Systeme, Perspektiven. Auflage. Wiesbaden, Vieweg & Sohn Verlag. 1032 (in German).

8. Zvonov V. A., Zaigraev L. S., Chernykh V. I., Kozlov, A. V. (2004) Ecology of Automotive Internal Combustion Engine. Lugansk: Publishing House of Volodymyr Dahl East Ukrainian National University. 268 (in Russian).

9. Parsadanov I. V. (2003) Improvement of Quality and Competitiveness of Diesel Engines Based on the Fuel and Environmental Criterion. Kharkov, Publishing Centre of National Technical University “Kharkiv Polytechnic Institute”. 244 (in Russian).

10. Kulchitskii A. R. (2000) Toxicity of Automotive and Tractor Engines. Vladimir, Vladimir State University. 256 (in Russian).

11. Kukharonak G. M., Berezun V. I. (2013) Diesel Emission Reduction. Sovershenstvovanie Organizatsii Dorozhnogo Dvizheniya i Perevozok Passazhirov i Gruzov: Sbornik Nauchnykh Trudov [Improvement in Organization of Traffic and Transport of Passengers and Goods. Collection of Scientific Papers]. Minsk, Belarusian National Technical University, 314–323 (in Russian).

12. Berezun V. I. (2013) High-Performance Energy-Efficient Engines for Off-Road Vehicles. Problems and Prospects for Development of Transport Systems and Building Complex. Gomel, Belarusian State University of Transportation, 157–158 (in Russian).

13. Bosch R. (2004) Diesel Engine Control Systems. Moscow, Publishing House “Za Rulyom”. 480 (in Russian).

14. Kukharonak G. M., Berezun V. I. (2018) Influence of Fuel Supply and Exhaust Gas Recirculation on Emissions of Harmful Substances from Diesel Engines. Avtomobil’nуi Transport [Automotive Transport], (42), 5–11 (in Russian).

15. Kukharonak G. M., Petruchenko A. N., Berezun V. I. (2014) Diesel Engine Emissions Reduction. Moscow, Novoe Znanie Publ. 220 (in Russian).

16. Kukharonak G. M., Sevizdral S. P., Berezun V. I. (2012) Provision of Environmental Indicators of Euro-4 and Euro-5 Level for Automobile Diesels of the Minsk Motor Plant. Visti Avtomobilno-Dorozhniogo Institutu [Bulletin of Automobile and Highway Institue], (1), 95–105 (in Russian).

17. Kukharonak G. M., Berezun V. I. (2018) Improvement of Diesel Engine Workflow. Izobretatel [Inventor], (1), 37–40 (in Russian).

18. Kukharonak G. M., Predko A. V. (2002) Mathematical Model of Rotation of Air Charge in Diesel Cylinder. Vestnik BNTU [Bulletin of Belarusian National Technical University], (4), 50–54 (in Russian).

19. Predko A. V. (2006) Modeling Flow in Inlet of Internal Combustion Engine. Nauka – Obrazovaniyu, Proizvodstvu, Ekonomike: Materialy 4-i Mezhdunar. Nauch.-Tekhn. Konf. T. 1 [Science for Education, Production, Economy. Proceedings of the 4th International Scientific and Technical Conference. Vol. 1]. Minsk, Belarusian National Technical University, 262–265 (in Russian).

20. Kukharonak G. M., Predko A. V., Yurchuk K. N. (2008) Determination of Parameters of Inlet Channels Using Virtual Bench in Purge. Vmeste k Effektivnomu Dvizheniyu! Sb. Nauch. Statei Mezhdunar. Nauch.-Prakt. Konf. [Together for Effective Movement! Collection of Scientific Papers of International Scientific and Practical Conference]. Minsk, Belarusian National Technical University, 262–265 (in Russian).

21. Alyamovskii A. A., Sobachkin A. A., Odintsov E. V., Kharitonovich A. I., Ponomarev N. B. (2005) SolidWorks. Computer Modeling in Engineering Practice. Saints-Petersburg, Publishing House “BKhV-Peterburg”. 800 (in Russian).

22. Deich M. E. (1969) Technical Gas Dynamics. Moscow, Energiya Publ. 368 (in Russian).

23. Predko A. V. (1995) Methods for Experimental Study of Swirling Inlet Channels. Sostoyanie i Perspektivy Razvitiya Nauki i Podgotovki Inzhenerov Vysokoi Kvalifikatsii v BGPA. Materialy Mezhdunar. 51-i Nauch.-Tekhn. Konf. BGPA [State and Prospects for Development of Science and Training of Highly Qualified Engineers at Belarusian State Polytechnical Academy. Proceedings of the 51st International Scientific and Technical Conference at BSPA]. Minsk, Belarusian State Polytechnical Academy, 78–79 (in Russian).

24. Kukharonak G. M., Petruchenko A. N., Berezun V. I. (2014) Choice of Diesel Engine Combustion Chamber Shape. Visnik SevNTU [Bulletin of Sevastopol National Technical University], (152), 65–68 (in Russian).

25. Kukharonak G. M., Hershan D. G. (2011) Modeling of Characteristics for Fuel Jets and Parameters for Diesel Combustion Chamber. Vestnik BNTU [Bulletin of Belarusian National Technical University], (4), 35–39 (in Russian).

26. Kukharonak G. M., Berezun V. I. (2014) Choice of Shape for Combustion Chamber of Diesel Engine with Low Injection Intensity. Sovershenstvovanie Organizatsii Dorozhnogo Dvizheniya i Perevozok Passazhirov i Gruzov: Sb. Nauch. Tr. [Improvement in Organization of Traffic and Transport of Passengers and Goods. Collection of Scientific Papers]. Minsk, Belarusian National Technical University, 180–184 (in Russian).

27. Kukharonak G. M., Berezun V. I. (2018) Influence of Fuel Supply and Exhaust Gas Recirculation on Emissions of Harmful Substances from Diesel Engines. Avtomobil’nyi Transport [Automotive Transport], (42), 5–11 (in Russian).

28. Kukharonak G. M. (1999) High Speed Diesel Workflow. Methods and Means of Improvement. Minsk, Belarusian State Polytechnical Academy. 180 (in Russian).

29. Grekhov L. V., Ivashchenko N. A., Markov V. A. (2004) Fuel Equipment and Diesel Control System. Moscow, Legion-Avtodata Publ. 344 (in Russian).

30. Kukharonak G. M., Berezun V. I. (2014) Selection of Parameters for System of Diesel Engine Exhaust Gas Recirculation. Nauka i Tekhnika = Science & Technique, (1), 57–63 (in Russian).

31. Berezun V. I. (2014) Study of Methods for Organizing Exhaust Gas Recirculation. Nauka – Obrazovaniyu, Proizvodstvu, Ekonomike: Materialy 12-i Mezhdunar. Nauch.-Tekhn. Konf. T. 2 [Science for Education, Production, Economy: Proceedings of the 12th International Scientific and Technical Conference. Vol. 2]. Minsk, Belarusian National Technical University, 56–57 (in Russian).


Review

For citations:


Kuharonak G.M., Klesso M., Predko A., Telyuk D. Organization of Six-Cylinder Tractor Diesel Working Process. Science & Technique. 2021;20(5):427-433. https://doi.org/10.21122/2227-1031-2021-20-5-427-433

Views: 552


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2227-1031 (Print)
ISSN 2414-0392 (Online)