Using Artificial Neural Networks to Determine Wear of Composite Friction Material

Sintered friction materials are widely used in friction units of automotive vehicles and special purpose vehicles.  The main purpose is to transmit torque to the actuator. The development of the technology market requires the development and use of new units. At the same time, the creation of new materials is required, which also applies to sintered friction materials. This group of materials is characterized by a high service life, efficiency of torque transmission, as well as the ability to restore performance in case of violation of operating modes. One of the most significant parameters characterizing  a sintered friction material is wear resistance. In most cases, it determines not only the resource of the unit itself, but the entire machine as a whole. A special place is occupied by brake units, which also use friction materials. The increased wear  resistance of the friction material contributes to a decrease in the efficiency and service life of the brake system. Evaluation  of the wear resistance of a friction material for the given operational parameters is a very long and costly process. The development of methodology and methods for accelerating the assessment of wear resistance is an important scientific and practical task. The paper presents the results of using artificial neural networks to predict the service life of a composite friction material based on copper on the sliding speed, pressure on the material and the amount of lubricant supplied to the friction zone. An artificial neural network has been trained using an array of experimental data for the FM-15 friction material.  The training results have shown high accuracy, correctness of the proposed and implemented network architecture. The developed software has demonstrated its efficiency and the possibility of using it in calculations to determine the wear of a composite friction material.

1. State Standard 27.002–2015. Reliability in Technology. Terms and Definitions. Moscow, Standartinform Publ., 2016. 24 (in Russian).

2. Safonov B. P., Begova A. V. (2004) Engineering Tribology: Assessment of Wear Resistance and Resource of Tribocouplings. Novomoskovsk, D. I. Mendeleev University of Chemical Technology of Russia, Novomoskovsk Institute. 59 (in Russian).

3. Voytov V. A., Zakharchenko M. B. (2015) Modeling the Processes of Friction and Wear in Tribosystems under Boundary Lubrication Conditions. Part 2. Simulation Results. Problemi Tribologії = Problems of Tribology, (2), 36–44 (in Russian).

4. ТU [Technical Specifications] BY 100219793.431–2015. Powder Friction Products. Minsk, The State Scientific Institution “Powder Metallurgy Institute Named after O. V. Roman”, Gosstandart Publ., 2015. 25 (in Russian).

5. Ilyushchenko А. Ph., Dmitrovich A. A., Leshok A. V. (2011) Sintered Metal-Ceramic Friction Composite Materials and Products. Vestsi Natsyyanal’nai Akademii Navuk Belarusi. Seryya Fizika-Technichnych Navuk = Proceedings of the National Academy of Sciences of Belarus. Physical-Technical Series, (2), 10–17 (in Russian).

6. Leshok A. V., Dyachkova L. N., Ilyushchenko A. F., Rogovoy A. N., Alekseenko N. A. (2019) Influence of Copper Frictional Material Composition on Structure and Tribotechnical Properties. Journal of Friction and Wear, 40 (6), 495–500. https://doi.org/10.3103/s1068366619060151.

7. Yudin E. G. (2004) Prediction on Durability of Friction Units in Transmissions of Tracked Vehicles. Vestnik MGTU imeni N. E. Baumana = Herald of the Bauman Moscow State Technical University. Series Mechanical Engineering, (3), 3–14 (in Russian).

8. Sprizhitskii I. A. (1984) Optimization of Design and Prediction of Durability of Friction Pairs of Clutch Couplings. Minsk. 191 (in Russian).

9. Shilkin N. V., Brodach M. M. (2019) Neural Networks: Possibilities of Using Self-Learning Algorithms in Control Systems for Heat and Power Consumption of Buildings. AVOK [AVOK – Association of Engineers for Heating, Ventilation, Air-Conditioning, Heat Supply and Building Thermal Physics], (4). Available at: https://www.abok.ru/for_spec/articles.php?nid=7229 (Accessed 10 December 2020) (in Russian).

10. Altunin K. A., Sokolov M. V. (2016) Application of Neural Networks for Modeling the Turning Process. Vestnik TGTU [Bulletin of Tambov State Technical University], 22 (1), 122–133 (in Russian).

11. Popov O. V., Popova Yu. B., Yatsynovich S. V. (2018) Determination of Limiting Resistance for Dilatant Soil to Shearing while Using Artificial Neural Networks. Nauka i Tekhnika = Science and Technique, 17 (6), 471–477. https://doi.org/10.21122/2227-1031-2018-17-6-471-477 (in Russian).

12. Popova Yu. B., Yatsynovich S. V. (2017) Software Implementation of an Artificial Neural Network for Managing Virtual Objects. Sistemnyi Analiz i Prikladnaya Informatika = System Analysis and Applied Information Science, (4), 72–78. https://doi.org/10.21122/2309-4923-2017-4-72-78 (in Russian).

13. Tarkhov D. A. (2005) Neural Networks. Models and Algorithms. Moscow, Radiotekhnika Publ. 256 (in Russian).