Preview

Electrochemical Cutting of Micro-Holes in Tubular Stepped Concentrator-Waveguide for Medical Purposes

https://doi.org/10.21122/2227-1031-2019-18-5-386-394

Abstract

A great attention has been recently paid to development of ultrasound technologies for treatment of blood vessels throughout the world. Authors of the paper have developed a new effective treatment method and ultrasound equipment that allow to carry out destruction of intravascular formations with simultaneous increase in elasticity of a vascular wall together with cardiologists from Belarusian Medical Academy of Postgraduate Education and Republican Scientific and Practical Center “Cardiology”. Advantages of the method are absence of necessity in surgical intervention, low probability of complications, low cost of treatment. The main component of the developed ultrasonic equipment is a tube-type stepped concentrator-waveguide having a spherical tip at a distal end with a single axial hole of 0.5 mm-diameter and three radial holes of 0.3 mmdiameter located at an angle of 120° relative to each other. The main effect for application of the concentratorwaveguide is achieved by ultrasonic vibromechanical action of a spherical tip on intravascular formation with subsequent removal of destruction products by their aspiration from a vascular bed. An additional effect is provided due to cavitation action on vascular formation and vessel walls by flow of fluid supplied via an internal cavity of the stepped concentratorwaveguide through the holes in the spherical tip. This contributes to a significant improvement in elastic properties of a vascular wall in atherosclerosis and diabetes. It is necessary to ensure high accuracy and quality of surfaces for the formed microholes in order to achieve maximum efficiency of the cavitation jet impact on intravascular formations and on the vascular wall. According to the analysis results on specific features of existing methods for small-diameter hole shaping, an electrochemical hole cutting method has been proposed which allows to obtain accurate micro-holes with a diameter of 0.3 mm and high surface quality in parts of small cross section and rigidity. The paper presents results of study on effect of electrochemical holes cutting parameters (voltage, concentration and consumption of electrolyte) on size and shape of the formed microholes. Main modes of electrochemical holes cutting process have been developed which allow to form micro-holes in a spherical tip of a tubular concentrator-waveguide with required accuracy, dimensions and shape.

About the Authors

Yu. G. Aliakseyeu
Belarusian National Technical University
Belarus
Minsk


A. Yu. Korolyov
Belarusian National Technical University
Belarus

Address for correspondence: Korolyov Aleksandr Yu. – Belarusian National Technical University, 24 Ya. Kolasa str., 220013, Minsk, Republic of Belarus. Tel.: +375 17 292-25-98     korolyov@park.bntu.by



A. S. Budnitskiy
Belarusian National Technical University
Belarus
Minsk


Dai Wenqi
Belarusian National Technical University
Belarus
Minsk


References

1. Alekseev Yu. G., Korolev A. Yu., Minchenya V. T., Niss V. S., Parshuto A. E., Khrustalev B. M. (2015) Combined technology for manufacturing of flexible ultrasonic concentrators-instruments. Minsk, Belarusian National Technical University. 203 (in Russian).

2. Fomikhina I. V., Litovskaya Yu. O., Alekseev Yu. G., Korolev A. Yu., Niss V. S. (2008). Influence of Electrolytic-Plasma Treatment on Structure and Properties in Surface Layer of Authentic Stainless 12Х18Н10Т Steel. Vestsi Natsionalnoy Akademii Navuk Belarusi. Ser. Fiz.Tekhn. Navuk = Bulletin of National Academy of Science of Belarus. Series of Physical and Technical Sciences, (3), 24-29 (in Russian).

3. Alekseev Yu., Korolev A., Parshuta A., Niss V. (2012). Model for Metal Removal in Electrolyte-Plazma Treatment of Cylindrical Surfaces. Nauka i Tekhnika = Science & Technique, (3), 3-6 (in Russian).

4. Aliakseyeu Y. G., Korolyov A. Y., Parshuto A. E., Niss V. S. (2017) Electrolyte-Plasma Treatment under Non-Stationary Mode in a High-Gradient Electric Field. Nauka i Tekhnika = Science & Technique, 16 (5), 391-399 (in Russian). https://doi.org/10.21122/2227-1031-2017-16-5-391399

5. Aliakseyeu Y. G., Korolyov A. Y., Niss V. S., Parshuto A. E., Budnitskiy A. S. (2018) Electrolyte-Plasma Polishing of Titanium and Niobium Alloys. Nauka i Tekhnika = Science & Technique, 17 (3), 211–219 (in Russian). https://doi.org/ 10.21122/2227-1031-2018-17-3-211-219

6. Alekseev Y. G., Korolyov A. Y., Niss V. S., Parshuta A. E. (2016) Electrolytic-plasma treatment of internal surface in tubular products. Nauka i Tekhnika = Science & Technique, 15 (1), 61–68 (in Russian). https://doi.org/10.21122/2227-1031-2016-15-1-61-68

7. Minchenya V. T., Adzerikho I. E., Korolev A. Yu. (2016) The use of ultrasonic concentrators-waveguides of tubular type to eliminate the obstruction of blood vessels. Doklady Belorusskogo gosudarstvennogo universiteta informatiki i radioèlektroniki = Doklady BGUIR, 101 (7), 300–303 (in Russian).

8. Minchenya V. T., Korolev A. Yu., Dai Wenqi (2018) Investigations on forming process while using drawing method for stepped surfaces of ultrasonic concentrators-waveguides of tubular type to eliminate obstruction of blood vessels. Materialy, Oborudovanie i Resursosberegayushchie Tekhnologii: Materialy Mezhdunar. Nauch. tekhn. Konf., 26-27 apr. 2018 g. [Materials, Equipment and Resource Saving Technologies: Proceedings of International Scientific and Technical Conference, Apr. 26-27, 2018]. Mogilev, Belarusian-Russian University, 41–42 (in Russian).

9. Yuriev A. S. (2001) Handbook for calculation of hydraulic and ventilation systems. Saint Petersburg, Mir i Semya Publ. 1154 (in Russian).

10. Cheng Yong Wang, Yue Xian Song, Yang L.P., Qu Y.P., Ping Ma, Fu L.Y. (2011) A review on Drilling Printed Circuit Boards. Advanced Materials Research, 188, 441–449. https://doi.org/10.4028/www.scientific.net/amr.188.441

11. Li Juan Zheng, Cheng Yong Wang, Yun Peng Qu, Yue Xian Song, Lian Yu Fu (2014) Interaction of Cemented Carbide Micro-Drills and Printed Circuit Boards During Micro-Drilling. International Journal of Advanced Manufacturing Technology, 77 (5-8), 1305–1314. https://doi.org/10.1007/s00170-014-6520-1

12. Romoli L., Rashed C.A.A., Lovicu G., Dini G., Tantussi F., Fuso F., Fiaschi M. (2014) Ultrashort Pulsed Laser Drilling and Surface Structuring of Microholes in Stainless Steels. CIRP Annals, 63 (1), 229–232. https://doi.org/10.1016/j.cirp.2014.03.053

13. Wang X.D., Michalowski A., Walter D., Sommer S., Kraus M., Liu J.S., Dausinger F. (2009) Laser Drilling of Stainless Steel with Nanosecond Double-Pulse. Optics & Laser Technology, 63 (2), 148–153. https://doi.org/10.1016/j.optlastec.2008.05.021

14. Jiang Jing (2014) Research on Microporous Machining Technology of Metal Materials by Picosecond Laser. Beijing, Beijing University of Technology Master Thesis. 61.

15. Luo Zhang [et al.] (2018) Research on Femtosecond Laser Efficient Parallel Micro-Hole Machining Technology. Journal of Hubei University of Technology, 33 (4), 19–21 (in China).

16. Zhao W. [et al.] (2018) Ultrashort Pulse Laser Micropore Processing. Infrared and Laser Engineering, 10, 1–9.

17. Liu L. Y. [et al.] (2015) Experimental Study on Picosecond Laser Processing of Stainless Steel Micropores. Applied Laser, 35 (4), P. 472–478.

18. Kong M. C., Axinte D., Voice W. (2010) Aspects of Material Removal Mechanism in Plain Waterjet Milling on Gamma Titanium Aluminide. Journal of Materials Processing echnology, 210, 573–584. https://doi.org/10.1016/j.jmatprotec.2009.11.009

19. Wang J., Guo D. M. (2003) The Cutting Performance in Multipass Abrasive Waterjet Machining of Industrial Ceramics. Journal of Materials Processing Technology, 133, 371–377. https://doi.org/10.1016/s0924-0136(02)01125-1

20. Azhari A., Schindler C., Kerscher E., Grad P. (2012) Improving Surface Hardness of Austenitic Stainless Steel Using Waterjet Peening Process. The International Journal of Advanced Manufacturing Technology, 63, 1035–1046. https://doi.org/10.1007/s00170-012-3962-1

21. Azmir M. A., Ahsan A. K. (2009) A Study of Abrasive Water Jet Machining Process on Glass/Epoxy Composite Laminate. Journal of Materials Processing Technology, 209, 6168–6173. https://doi.org/10.1016/j.jmatprotec.2009.08.011

22. Grachev M. V. (2018) Comparison of Technological Methods for Small Diameter Hole Perforation in Titanium Alloys. International Journal of Engineering & Technology, 7 (3), 105–107. https://doi.org/10.14419/ijet.v7i3.19.16995

23. Amitan G. L., Baisupov I. A.,Baron Yu. M., Volosatov V. A. (1988) Handbook on electrochemical and electrophysical processing methods. Leningrad, Mashinistroyenie Publ. 719 (in Russian).

24. Moroz I. I. (2009) Electrochemical dimensional processing of metals. Moscow, Mashinistroyenie Publ. 279 (in Russian).


Review

For citations:


Aliakseyeu Yu.G., Korolyov A.Yu., Budnitskiy A.S., Wenqi D. Electrochemical Cutting of Micro-Holes in Tubular Stepped Concentrator-Waveguide for Medical Purposes. Science & Technique. 2019;18(5):386-394. (In Russ.) https://doi.org/10.21122/2227-1031-2019-18-5-386-394

Views: 1057


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2227-1031 (Print)
ISSN 2414-0392 (Online)