Preview

PARAMETERS OF LASER PROCESSING AND THEIR INFLUENCE ON TRIBOLOGICAL CHARACTERISTICS OF IRON-BASED COATINGS

https://doi.org/10.21122/2227-1031-2018-17-1-56-63

Abstract

The paper considers improvement of physic-mechanical and operational properties of adhesive coatings after laser infusion with additional alloying В4С, ТаВ and МоВ. Influence of the laser infusion with additional alloying on structure, microhardness and wear-resistance of adhesive coatings of the Fe–Cr–B –Si system has been studied in the paper. While increasing a laser beam velocity microstructure is changed from equilibrium to quasi-eutectic. Presence of molybdenum boride and tantalum increases sensitivity of the coating to specific features of laser remelting. In both cases heat exchange conditions have been changed, a number of iron and chromium borides has been increased and due to this molybdenum and tantalum have been partially passing to free state that contributes to a disintegration of structural components. While introducing solid particles B4C into a coating they are dissolved in an iron matrix while being heated by a laser beam and under cooling they are isolated in the form of separated Fe an Cr boride inclusions. Laser infusion and alloying increase coating wear-resistance. Load increase from 30 to 70 Н improves coating wear resistance averagely by 15–26 % and wear resistance of non-alloyed coatings is improved by 26–43 %. An increase of melting rate and laser spot diameter does not exert significant influence on wear but an increase in overlapping coefficient leads to reduction of coating wear. Presence of solid particles in a coating and an increase in rate of melting by laser beam reduce coating wear resistance. Such rather complicated dependence of coating wear rate on conditions of laser melting and wearing process is due to a complex of structural and phase transformations which have contributed to formation of secondary solid inclusions and increased microhardness.

About the Authors

O. V. Diachenko
Belarusian National Technical University
Belarus

Address for correspondence: Diachenko Оlga V. – Belarusian National Technical University, 67 Nezavisimosty Ave.,220013, Minsk, Republic of Belarus. Tel.: +375 17 293-95-81    tiro@bntu.by

 



M. A. Kardapolova
Belarusian National Technical University
Belarus


References

1. Il’iushchenko, A. F., Okovityi, V. A., Kundas, S. P., Formanek, B. (2002) Formation of Gas and Thermal Coatings tings: Theory and Practice. Minsk, Bestprint. 480 (in Russian).

2. Vityaz P. A., Il’yushchenko A. F., Shevtsov A. I. (2006) Fundamentals on Deposition of Wear-Resistant, Corrosion-Resistant and Heat-Resistant Coatings. Minsk, Belaruskaya Navuka Publ. 363 (in Russian).

3. Grogoryants A. G., Shiganov I. N., Misiourov A. I. (2006) Technological Processes of Laser Processing. Moscow, Publishing House of Bauman Moscow State Technical University. 664 (in Russian).

4. Yandimirkin E. M. (2006) Phase Composition and Structure of Surface Layers of Constructional and Instrument Steel During Laser Doping with the Help of Boron Carbide. Fizika i Khimiya Obrabotki Materialov = Physics and Chemistry of Materials Treatment, (3), 38–41.

5. Vencl A., Mrdak M., Cvijovi? I. (2006) Microstructures and Tribological Properties of Ferrous Coatings Deposited by APS (Atmospheric Plasma Spraying) on Al-Alloy Substrate. FME Transactions, 34 (3), 151–157.

6. Hemmati I., Huizenga R. M., Ocelík V., De Hosson J. T. M. (2013) Microstructural Design of Hardfacing Ni–Cr–B–Si–C Alloys. Acta Materialia, 61 (16), 6061–6070. DOI: 10.1016/j.actamat.2013.06.048.

7. Dyachenko O. V., Kardapolova M. A., Devoyno Yu. O. (2005) Prospects for Obtaining Coatings of System-Fe–Cr–B–Si while Using Laser Modification. Vestnik Brestskogo Gosudarstvennogo Tekhnicheskogo Universiteta [Bulletin of Brest State Technical University], (4), 12–15 (in Russian).

8. Dyachenko O. V., Kardapolova M. A. (2007) Study of Tribological Characteristics for Adhesive Iron-Based Coatings with the Help of Simplex Method. Inzheneriya Poverkhnosti: sb. tr. Mezhdunar. Nauch.-Tekhn. Konf. Brest, 25–27 okt. [Surface Engineering: Collected Papers of International Scientific and Technical Conference. Brest, October 25–27]. Brest, Brest State Technical University, 33–37.

9. Feldstein E., Kardapolova ?., Dyachenko O. (2015) Structure, Phases and Tribological Behaviour of Fe-Based Self-Fluxing Alloy Coatings Formed by Plasma Spraying and Follow-Up Flame and Laser Remelting. International Journal of Surface Science and Engineering, 9 (5), 395–406. DOI: 10.1504/IJSURFSE.2015.072059.

10. Abdolahi B., Shahverdi H. R., Torkamany M. J., Emami M. (2011) Improvement of the Corrosion Behavior of Low Carbon Steel by Laser Surface Alloying. Applied Surface Science, 257 (23), 9921–9924. DOI: 10.1016/j.apsusc.2011.06.108.


Review

For citations:


Diachenko O.V., Kardapolova M.A. PARAMETERS OF LASER PROCESSING AND THEIR INFLUENCE ON TRIBOLOGICAL CHARACTERISTICS OF IRON-BASED COATINGS. Science & Technique. 2018;17(1):56-63. (In Russ.) https://doi.org/10.21122/2227-1031-2018-17-1-56-63

Views: 816


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2227-1031 (Print)
ISSN 2414-0392 (Online)